
Hydraulic Elevator Cylinder Repacks in Oregon
If your elevator sinks at the floor, leaks oil, or drifts down when nobody is in it, the cylinder seals are worn. A repack replaces them for a fraction of what a new cylinder costs.
Is Your Elevator Sinking or Leaking Oil?
The usual signs are easy to spot once you know what you are looking at.
All four point the same way. Hydraulic fluid is escaping past the seals on the cylinder, and the fix is a repack.
Talk To Us About a RepackThe car settles at the floor
You arrive at a landing, the doors open, and over the next minute the car quietly drops an inch or two. On the way back it has to level up again.
The elevator drifts down when parked
Leave it at an upper floor overnight and by morning it has sunk, sometimes far enough that it has to relevel before the doors will open.
There is oil in the pit
A film on the pit floor, a damp patch under the cylinder, or a reservoir that needs topping up more often than it used to.
The ride feels different
Slower to start, a small drop as it sets off, or a car that no longer sits quite level.

What Is a Cylinder Repack?
A hydraulic elevator is lifted by a piston pushing up out of a cylinder, driven by fluid under pressure. Where the piston leaves the cylinder there is a set of seals, called packing, that keeps the fluid in.
Those seals wear. They are rubber components under constant pressure and movement, and after enough years they stop sealing perfectly. Fluid escapes past them, which is why the car sinks and why oil appears in the pit.
A cylinder repack replaces that packing. The elevator is taken out of service, the piston is lifted clear, the worn seals are removed, new packing is fitted, and the system is refilled and tested. The cylinder itself stays where it is.
It is one of the more common jobs on an older hydraulic elevator, and on the scale of elevator work it is a straightforward one.
Do I Need a Repack or a New Cylinder?
Not every leak is a seal, and this is worth getting right before anyone quotes you.
How we tell the difference
We look at where the fluid is escaping, the condition of the piston surface, and how the system behaves under pressure. On an in-ground cylinder we look at whether fluid is being lost into the ground rather than into the pit, which is the sign that the problem is the cylinder rather than the seals.
If the answer is a new cylinder we will say so, and if it is a repack we will say that too. The difference in cost between them is significant enough that it deserves an honest answer.
A repack is the answer when...
...the seals have worn. The cylinder is sound, the fluid is escaping at the packing, and replacing the seals resolves it. This is the usual case and by far the less expensive of the two.
A new cylinder is the answer when...
...the cylinder itself has failed. Corrosion on an in-ground cylinder, scoring on the piston, or a breach in the casing cannot be fixed with new packing.
In-ground cylinders in particular can corrode where they sit below the pit floor, and a leak there is a different problem entirely.
How we tell the difference
We look at where the fluid is escaping, the condition of the piston surface, and how the system behaves under pressure. On an in-ground cylinder we look at whether fluid is being lost into the ground rather than into the pit, which is the sign that the problem is the cylinder rather than the seals.
If the answer is a new cylinder we will say so, and if it is a repack we will say that too. The difference in cost between them is significant enough that it deserves an honest answer.
How a Cylinder Repack Works
Replacing the seals on a hydraulic cylinder is a straightforward process when handled by experienced technicians.
We confirm the diagnosis
We check where the fluid is going and rule out the alternatives. Sinking can occasionally be a valve rather than the packing, and that is a cheaper fix.
We quote before we start
You get told what the job involves, what it costs, and how long the elevator will be out of service.
We do the work
The elevator comes out of service, the piston is lifted, the old packing is removed and replaced, and the system is refilled.
We test and hand back
We run the elevator, check the levelling, confirm there is no further loss, and put it back into service.
Why Oregon Calls Us for Repacks

We diagnose before we quote.
Sinking is not always the packing. We find out what is actually causing it rather than quoting the biggest job that fits the symptom.

We will tell you if it is the cylinder.
A repack on a failed cylinder is money wasted. If the problem is the cylinder itself, you need to know that before anyone starts.
We know old hydraulics.
Four generations in Oregon means a lot of hydraulic elevators, including equipment installed long before the current designs. Older cylinders behave differently and we have seen most of them.

We source the packing.
Seals for older or discontinued equipment can be difficult to find. We source nationally and internationally, which is often the difference between repacking and being told to replace.
Cylinder Repacks Across Oregon
We repack hydraulic elevators in all six regions.
Not sure if we reach you? Call us. We cover the whole state.
Cylinder Repack Questions, Answered
A hydraulic elevator that settles or drifts down while parked usually has worn cylinder seals allowing fluid to escape past the packing. The repair is a cylinder repack, which replaces the seals. Occasionally the cause is a valve rather than the packing, which is why the fault should be diagnosed before work is quoted.

Ready to talk elevators?
Tell us what your elevator is doing and we will tell you what is causing it. If it is a repack we will say so, and if it is something else we will say that instead. Four generations of Oregon elevators behind every answer.





